Assembly and setup

Build your Brainrich, one step at a time.

Step-by-step videos for every gym and layout, what to get ready before build day, and fixes for the questions parents ask us most while they build.

Two girls climbing a finished Spider Max V3, with crash mats around it A finished Spider Max V3, mats around it
  • 4 to 6 hoursfor a tension gym with two adults (5 to 7 for a Mega Max V3). A wall gym takes about an afternoon.
  • Tools in the boxYou add a bubble level, a step ladder and plywood boards for the ceiling.
  • A person to call1-800-586-1688, or ask for a video call and we’ll look at it with you.
Step-by-step videos

Pick your gym, then your layout.

Each video follows one gym in one layout, from the first bolt to the finished gym. There’s no sound: every step is shown on screen, and the part numbers match the ones in your paper manual. Pause as often as you need.

1Your gym

2Your layout

  • Light or no-net version? It builds the same way. Skip the steps for parts your kit doesn’t include.
  • Adding Monkey Bars V3 to your gym? Watch Spider V3, Bars. A Spider V3 is a T3 plus one monkey bar set, so its second-ladder and monkey bar chapters show the same parts.
  • Hiring help? Send them this page. A handyman or contractor can follow the same step-by-step videos. Our handyman hiring guide shows where to book one and what to tell them. Older V2 gym? See the V2 videos.
  • Installing it for a customer? Start with our installer guide: what to bring, how two people share the work, and the ceiling and floor rules. ¿Habla español? Guía en español.
Before you start

Get ready before build day.

Owners tell us these are the things they wish they’d sorted first. Tick them off as you go; your ticks stay saved on this device.

0 of 8 done

Have these ready

In the boxes

The wrenches and keys the gym needs, and every nut and bolt, already marked.

You add

  • A bubble level
  • A step ladder
  • A stud finder, for drywall ceilings and wall gyms
  • Plywood boards (see the table)
  • A Phillips screwdriver, for the rung bolts behind the pole plugs
  • Wall gyms only: a drill with a 6 mm (¼ in) bit

Nice to have

An impact driver speeds up the rung bolts. Lightly tighten everything first, then go around at the end and secure every bolt by hand, without overtightening.

Boxes and boards by gym

GymBoxesCeiling boards
Model T341
Spider V36Tall kit: 82
Spider Max V37Tall kit: 103. For the Fort, cut one in half.
Mega Max V39Tall kit: 134. A net-top section with a single pole: cut one in half.
W32Screws go into wall studs. A 12 mm (½ in) plywood board behind the brackets protects the wall.
W3 Max3

Tall kits add one extension ladder box per ladder. Count doesn’t match? Call or email us before you open anything.

The build at a glance

Six steps for a tension gym.

Every tension gym goes up the same way, one ladder at a time. Tap Watch to jump to that step in the video you picked above.

  1. 01

    Build the ladder on the floor

    Rungs between the two poles, caps on the bolts. A few rungs ship in the pull-up bar or monkey bar box, so the ladder box can look short.

  2. 02

    Add the top and the feet

    The telescopic poles, the top supports and the screw feet go on while the ladder is still on the floor.

  3. 03

    Stand it up under its board

    One adult at the top by the ceiling holds the ladder straight and sets the plywood board between the top supports and the ceiling, under a joist, while the other turns the screw feet at the bottom.

  4. 04

    Set the height and tighten

    Pin the poles at the right height. While one adult holds the ladder, the other turns the screw feet until the top presses on the ceiling, plus a couple more turns. Firm, not cranked: don’t overtighten.

  5. 05

    Level it

    Hold a bubble level on each pole, at the top and at the bottom, turning it a quarter turn at a time to check every side.

  6. 06

    Add the bars, net and hang-ons

    Pull-up bars, then monkey bars, then the net and accessories. Lightly tighten everything first, then go around and secure every bolt. The test: an adult should be able to hang from it without it moving.

Wall gyms (W3 and W3 Max)

  1. Build the ladder and the monkey bar frame on the floor.
  2. Find the wall studs with a stud finder. They’re usually 16 or 24 in (40 or 61 cm) apart.
  3. Hold the frame against the wall, level it and mark the holes.
  4. Drill 6 mm (¼ in) pilot holes into the studs.
  5. Screw the brackets to the studs, then add the net clips, the net and the accessories.
Fix a problem

The questions parents ask us mid-build.

The questions parents ask us while they build, and our answers. Search for a word, or open a question.

Boxes and parts

Only some of the boxes came

That’s normal. Your gym ships in several boxes, often with different carriers, and they can arrive on different days. Check your shipping emails for every tracking number. If one still hasn’t come once the rest are in, call 1-800-586-1688 or email us with your order number.

The ladder box looks short on rungs

That’s expected. The rungs are spread across the boxes: some ship in the pull-up bar or monkey bar box, and it’s normal for a ladder not to have every step filled. The video says so on screen at the end of the ladder chapter.

A part is missing

Look in every box first, including the foam, inside the bars and the skinny pull-up bar box, which tends to end up at the bottom of the pile. Still missing? Email info@brainrichkids.com with your order number and a photo of each box label and what was inside. If something is missing from a new delivery, we’ll send it.

I have bolts left over

That’s normal: every box packs a few spares. Before you put them away, check the monkey bar clamps. A #12 bolt with its cover goes in the hole just under each clamp as a stopper.

Which bolt goes where?

Every nut, bolt and part is marked, and the video shows the same part numbers on screen as your paper manual. Sort the small parts into the empty boxes as you open them, so nothing rolls away.

The round nut on a clamp is showing

That’s by design. The head of the clamp nut is smooth and rounded, and it stays exposed once installed. It doesn’t get a rubber cover.

A rubber cap won’t stay on

Press it on firmly by hand. If it still falls off or arrived cracked, email us a photo and we’ll sort it out.

During the build

The gym wobbles

It shouldn’t. An adult should be able to hang from it without it moving. Check that the top telescopic pole is out to the right hole with no gap at the ceiling, that the small plastic piece at the bottom of the telescopic bar is in place, that every bolt is fully tightened, and that the floor under the feet is solid. Still moving? Call 1-800-586-1688 and we’ll look at it with you.

There’s a gap at the top, or it won’t press firmly

Don’t stack more plywood. Make the bottom bolt a little shorter and pull the top telescopic pole (the one with the row of holes) out to the next hole, then tighten again.

The monkey bars slide down the poles

Add the stopper: the extra #12 bolt from the ladder box goes, with its cover, in the hole just under each clamp. Move the clamp up slightly to line it up with the hole.

A clamp nut won’t thread

Don’t force it. Email us a photo of the clamp and we’ll send a new clamp set.

Can I swap pin #76 for a bolt?

No. The pin is smooth on purpose: a bolt’s threads make it weaker, and it can bend. Use the pin that came with the gym.

Can a bar hang off just one pole?

No. Never attach an L-shaped bar to a single pole. Build the layout the way your video shows it.

There’s a beam or slope where a pole goes

Every pole needs a flat ceiling above it. Even a slope of about an inch makes the pressure uneven, and a plywood board doesn’t fix the angle. Open beams or rafters work with plywood laid across them. For slanted ceilings, a wall-mounted W3 or W3 Max is the answer.

After it’s up

A rung is loose

Pop off the plastic plugs on the pole, re-tighten the rung bolts with a Phillips screwdriver, and check the other rungs too, especially after a move. Don’t crank them with the metal key: over-tightening can crack the rung cups. If a rung came off completely, email us, because it goes back on with a new set of bolts.

It feels looser after a few weeks

Tension can drop a little as everything settles in, and carpet compresses. Check it every week, give the screw feet a turn if there’s any gap at the ceiling, and go over the clamps and bolts once a month.

Marks on the ceiling

That’s what the plywood boards prevent. Put a board between each ladder’s top and the ceiling. It’s held by the tension, never screwed in.

We’re moving it to another room

It’s a two-person job. Release the tension at the feet while someone holds the frame, then take it down in reverse order. Prise the grey caps off carefully with a butter knife. When it goes back up, re-tighten every rung.

Adding a swing or another accessory

Clip hang-ons to the ring hooks or ring bolts with a carabiner, and set the height to suit each child. Don’t hook bare metal carabiners straight over the monkey bars: they chip the paint and slide. See the hang-on videos.

Nothing matches. Call 1-800-586-1688 or email info@brainrichkids.com and tell us which step you’re on.

Safety and care

Keep it tight, padded and supervised.

  • Check it every weekCheck the tension and that nothing has shifted. Once a month, check every bolt, cap, clamp, rope and carabiner.
  • 220 lb per barRated for 220 lb on any one bar or set of monkey bars. Swings, rings, trapeze and ropes each have their own limit, generally 110 lb.
  • Mats around itCrash mats at least 6 cm thick around the gym, never under the feet. See our safety mats.
  • An adult in the roomKids play while you’re in the same room. Bare feet or grippy socks. No helmets, scarves or drawstrings on the gym.
  • Moving roomsTake it down in reverse order with two adults, then rebuild with the same video. Check for loose bolts and missing caps as it goes back up.
  • Something looks wrongA cracked cap, a frayed rope or a bent part: take that piece out of use and email us a photo. Replacement parts
Manuals

Need a paper manual?

Your gym’s manuals come in the boxes, and the videos above show every step. If you need an old manual, email us with your gym model and we’ll send you the right one.

Email us for a manual
Nets and hang-ons

Tie the net, hang the accessories.

Short videos on Instagram. The rings, trapeze, rope ladder and climbing rope adjust in height with the stoppers on their ropes, so set them to suit each child.

Older gyms

Own a V2 gym, a T2 or a W2?

The V2 assembly videos are on our YouTube channel. Want V3 monkey bars on a V2 frame? A Cross Bar V3 set converts it. Not sure which version you have? Email us a photo of a clamp and a rung, and we’ll tell you and send the right PDF manual.

From owners

What owners say about the build.

Assembly … is easiest done with two people. Once you move it a couple times, it gets faster.
Deborah, Spider Max owner, Oct 2026
Install was lengthy but relatively easy. My husband was able to install it mostly by himself!
Sheri, Spider V3 owner, Nov 2026
I’ll admit that when I set out to put this up I was pretty nervous. At first glance, it seemed fairly complicated. Thankfully my worries were completely unfounded.
Parker, W3 Max owner, Apr 2024
We got the plywood at Home Depot and they cut it for us and we spray painted it white. That was a pretty simple process…
Danielle, Spider Max V3 owner, Oct 2026
Get help

Stuck? A real person will help.

  • Call us1-800-586-1688Office hours: Monday to Friday, 10 am to 5 pm Eastern. We try to pick up in the evening and on weekends too: if we miss you, leave a voicemail and we’ll call you back. Tell us which gym and which step you’re on, and we’ll walk you through it.
  • Email a photoinfo@brainrichkids.comSend your order number, a photo of the part and one of the whole gym. Something didn’t arrive? Put “Missing parts” in the subject.
  • Video callWe’ll look at your gym with you on a FaceTime call. Call or email us to set a time.
  • Hire a proBuild it yourself, or hire a pro. A handyman can follow the same videos, so send them this page to look over first. We don’t have our own installers, so our handyman hiring guide shows where to book one near you and what to tell them.
  • Ask other ownersThe Brainrich Kids Chatter group on Facebook has 12,500 parents who share their builds and layouts.
Questions before you buy

Assembly, answered.

How long does it take to put together?

Plan on 4 to 6 hours for a tension gym with two adults (5 to 7 for a Mega Max V3), and about an afternoon for a wall gym. It’s easy, just not quick. You can also build in stages: once the first ladder is up, each extra monkey bar set takes about 45 to 90 minutes.

Do I need to drill?

Not for the tension gyms (Model T3, Spider V3, Spider Max V3 and Mega Max V3). They press between the floor and the ceiling, with no holes. The wall gyms (W3 and W3 Max) screw into the wall studs.

Can someone else build it for me?

Yes. Build it yourself, or hire a pro. A handyman or contractor can follow the same step-by-step videos. We don’t have our own installers, so our handyman hiring guide shows where to book one and what to tell them.

Will it mark or damage my ceiling?

The gym presses on the ceiling, so we recommend a 24 × 24 in plywood board between each ladder’s top and the ceiling. It spreads the load and protects the paint, it’s held by the tension (no screws), and a coat of ceiling paint makes it disappear. Set each top under a joist.

Can it stand on carpet?

Yes, if the carpet isn’t thick or fluffy. Carpet compresses overnight, so tighten the screw feet a little the next day. Never stand the feet on gym mats, foam tiles, play mats or rubber flooring: high-density gym mats are bouncy, and the whole gym can shift when kids swing. On wood or tile, keep the rubber pads under the metal feet.

What if my ceiling is sloped, beamed or very tall?

Tension gyms need a flat ceiling between 6′9″ and 10′5″. For slanted or very tall ceilings, the wall-mounted W3 and W3 Max are the answer.

Can we move it to another room later?

Yes. Take it down in reverse order with two adults, then rebuild it with the same video. Owners say it goes faster every time.

Can we add monkey bars or accessories later?

Yes. Every gym is modular: Model T3 plus a Monkey Bars V3 set makes a Spider V3, another set makes a Spider Max V3, and another makes a Mega Max V3. Swings and other hang-ons clip onto the ring hooks with a carabiner. See the add-ons.

Is there help if I get stuck?

Yes. Call 1-800-586-1688 (Monday to Friday, 10 am to 5 pm Eastern; if we miss you, leave a voicemail), email info@brainrichkids.com with a photo, or ask for a FaceTime call and we’ll look at your gym with you.

Still choosing?

Every Brainrich comes with these videos and a person to call.